Car Pulls Sideways
On a straight road, the car drifts left or right without steering input. Toe or camber errors are the usual cause, though a sticking caliper can mimic it.
Our wheel alignment service in Dubai measures camber, caster and toe at all four corners. We correct each angle to your maker's specification and finish with a road test before handover.
5-star on Google · 87 reviews
The facts
Toe has a huge effect on tyre life. On a light vehicle with toe at 0.00°, tyres can last around 92,000 km, but at an extreme 4.20° that falls to about 1,500 km. Most factory settings allow only a fraction of a degree, so even a bent tie rod can push a car well outside its window.
The same tests recorded up to 129% higher rolling resistance and roughly 37% more CO₂ across the misaligned range. Higher drag means the engine burns extra fuel just to keep the car moving. That is why we measure every vehicle against its factory figures rather than eyeballing the steering wheel.

Know the signs
These six symptoms usually show up before tyre damage becomes expensive.
On a straight road, the car drifts left or right without steering input. Toe or camber errors are the usual cause, though a sticking caliper can mimic it.
The rim sits noticeably tilted to one side while you drive straight ahead. This often follows a kerb strike or new suspension parts fitted without a geometry check.
One shoulder of the tread wears faster than the other, or the ribs feel feathered. Inner-edge wear points to camber, while saw-tooth patterns usually signal incorrect toe settings.
Tyres that squeal at normal roundabout speeds are being scrubbed sideways. The noise suggests the front wheels are fighting each other instead of rolling together in one direction.
The car needs constant small steering corrections on the open motorway. Low caster or worn steering joints reduce straight-line stability, which makes long drives tiring and less safe.
A hard knock against a kerb or pothole may twist steering links or a control arm without visible damage. A quick measurement confirms whether the angles have moved.
Each service below follows the factory specification for your exact model and trim.
We measure and adjust both axles on cars with independent rear suspension. Setting the rear first gives the front a true reference, which keeps the steering wheel centred.
Cars with a fixed rear beam only allow front adjustment. We set the front toe and camber to factory values, then confirm the rear axle runs straight behind it.
The thrust line shows where the rear axle points. We align the front wheels to that line, so the car tracks straight even when rear adjustment is limited.
Incorrect tilt wears one edge of the tyre. We correct camber using adjustable arms, eccentric bolts or slotted strut mounts, staying within the tolerance window your maker allows.
Caster gives the steering its self-centring feel and straight-line stability. We check side-to-side balance, because an unequal caster between left and right pulls the car toward the lower side.
Toe has the biggest effect on tread life. We lock the steering straight, then turn each tie rod until the front pair matches the specified factory toe value.
Uneven weight around a rim causes vibration through the steering column. We spin each assembly on a computerised balancer and add weights until both planes read within tolerance.
Front tyres usually wear faster than rear ones. We move them in the pattern your tyres and drivetrain allow, which evens out wear and extends the set's life.
Worn joints and bushes stop any setting from holding. We check every steering and suspension link for play first, so the new angles stay where we set them.
Air suspension and adjustable coilovers change geometry when the height changes. We set the correct factory ride height first, then set every angle at that exact loaded position.
Stability control relies on knowing exactly where the steering points. After the angles change, we recalibrate the sensor with diagnostic software, so no stability warning lights appear afterwards.
Lowered cars, track-day setups and staggered fitments need settings beyond the standard factory sheet. We agree the targets with you first, then record them for every future visit.
Three angles control how each tyre meets the road. The table shows what each one does and what we adjust.
| Angle | What It Measures | What Goes Wrong | What We Do |
|---|---|---|---|
| Camber | Inward or outward tilt seen from the front | Wear on one tyre edge | Adjust strut tops, eccentric bolts or arms |
| Caster | Forward or backward tilt of the steering axis | Wandering or heavy steering | Check and correct mounting points and bushes |
| Toe | Whether the tyres point in or out seen from above | Feathered tread and pulling | Set tie rods to the factory value |
Step by step
We first check tread depth, wear pattern and pressures, because a badly worn or underinflated tyre gives false readings on the aligner.
Ball joints, tie rod ends and bushes get tested for play. Any loose part gets reported first, before we touch the settings.
Precision targets clamp onto each rim, and high-resolution cameras read their positions to calculate the angles at every corner in real time.
Our technician sets rear camber and toe first, then front caster, camber and toe, following the exact order your maker's data specifies.
Diagnostic software resets the steering angle sensor, so stability control and lane systems know the wheels point straight ahead again after adjustment.
A short drive confirms the vehicle runs true and the steering sits level. You then receive and keep the printed before-and-after report.
Some events knock the geometry out straight away, while others shift it slowly. The table lists the moments we recommend a check.
| Trigger | Why It Matters |
|---|---|
| New tyres fitted | Fresh tread wears to whatever angle it starts on |
| Pothole or kerb impact | A single hard hit can bend a tie rod or arm |
| Suspension or steering parts replaced | New parts change the original settings |
| Every 10,000 to 12,000 km | Gradual wear slowly moves the angles |
| Lowering or lifting the car | Ride height changes camber and toe directly |
Why 800 Exotic
Each alignment is set by a MOIAT-certified technician who checks the factory data sheet for your specific model before turning a single adjuster bolt.
Rear-steer systems on Porsche and Mercedes-AMG models, plus air suspension on Range Rover, each get their own geometry routine from the maker's workshop data.
When a worn part stops the angles holding, we show you the reading and explain the fix rather than leaving the car partly aligned.
A four-wheel setup here uses the same factory data as the dealer, often at up to 30% under the price the dealer quotes.
A 5.0★ score from 87 Google reviewers reflects 15+ busy years of workshop experience and 50,000+ vehicles already returned safely to the open road.
Every completed job leaves with warranty terms on paper, covering the adjustment itself and any suspension or tyre part we replace on the day.
Slow Down for Potholes: Braking before a pothole rather than inside it reduces the force on steering joints.
Park Away From Kerbs: Rubbing or mounting kerbs while parking bends arms and knocks toe out of range.
Keep Pressures Correct: Equal, correct pressures stop the car pulling and help settings last longer.
Rotate Tyres Regularly: Swapping positions works best every 10,000 km and spreads wear evenly before patterns grow.
Watch Speed Bumps: Crossing slowly and straight protects bushes and ball joints from sudden loads.
Recheck After Repairs: Book a quick check whenever steering or suspension components are replaced.
Dubai · Abu Dhabi · Sharjah
We align cars at our workshops in Al Quoz, Musaffah and Sharjah Industrial Area 10, and each one holds factory geometry data for German, British, Italian, American and Asian makes. If a worn part turns up, the same branch replaces it during your visit. Our driver can fetch the car from your home or workplace for free, and roadside assistance is on hand after a heavy impact. Share the make, model and tyre size by WhatsApp to reserve a time.
Find our Al Quoz workshop on Google Maps
DubaiAl Quoz
Abu DhabiMusaffah
SharjahIndustrial Area 10Correct geometry protects your tyres, saves fuel and keeps the steering light and predictable. 800 Exotic measures every corner, corrects each angle and prints the proof. A quick message with your model details lets us arrange a convenient slot for your vehicle. Any car repair in Dubai found during the check can be handled on that same visit.
Answers
No. Alignment sets the angle each wheel meets the road, while balancing evens out weight around the wheel itself. Pulling points to alignment, and vibration usually points to balance.
A standard four-wheel job normally needs around one hour. Seized adjusters, ride height setting or sensor calibration on luxury models can add extra time to the visit.
Yes. Fresh tyres pick up any wear pattern from the very first kilometre, so a check protects your investment. Our tyre change and geometry work happen in one visit.
The price depends on whether one or both axles need adjustment, how many parts are adjustable and whether sensors need calibrating. We confirm the full figure before any work begins.
A sticking caliper or uneven tyre wear can also pull the car. We check those next, and our brake pads replacement team handles any binding brakes we find.
Yes. Loose bushes and joints let the wheels move under load, so settings drift soon after adjustment. Worn parts get replaced by our car suspension repair specialists before we align.
5-star rated on Google
Every one of our 87 Google reviews is 5 stars. Read what owners say about their repairs, then see the full list on our Google profile.
Offering a full range of services, state-of-the-art equipment, and years of experience, we promise the finest care for your vehicle.